Category: Article

邵

shaoyong@smthelp.net
whatsapp:+86 137 6048 1664
skype:sy332366

Able to clean top surface of PCB even chip components attached on the bottom side.
Antistatic bar (ionizer) is prepared as standard to neutralize static and to prevent dust from top surface of PCB.
Two Lanauge Display Chinese And English,easy Opertion.
Draw-out Design For Better Maintenance.
Professional Design And Production Clean Machine With Many Years Experience , We Know What Customer Requirement .

contact us：shaoyong@smthelp.net     WhatsApp：+86 137 6048 1664

The Telescopic Gate Conveyor from Electro Design is a fully automated pass through conveyor that allows people and vehicles to go through, rather than round a complete line. Since the retracted position of the telescopic conveyor is its idle position there is no need to press any buttons to pass through the line. Each side and section of the conveyor has its own motor drives and belts.
Working height (mm) 900±20(std)
Transport Speed 1-15meters per minute or as your specified
Power supply 100V, 220v,230V (single-phase AC)
Power Maximum 100 W
Belt type 4mm flat belt
Telescopic Length(mm) 850mm
Stretch out / retract 6 sec

contact us：shaoyong@smthelp.net    WhatsApp  ：+86 137 6048 1664

The Pcb Traverser Is Used For Transporting Boards From One Line Into Two Lines Or Vice Versa.
The Orientation Of The Board Is Not Changed During Traversing.

contact us：shaoyong@smthelp.net      WhatsApp：+86 137 6048 1664

The 90° PCB Turn Conveyor is used for changing the direction of flow of a PCB assembly line.
The PCB is transferred onto the built-in belt conveyor which turns either 90° clockwise or counter clockwise.

contact us：shaoyong@smthelp.net    WhatsApp：+86 137 6048 1664

Plc Control
Diameter: 3mm Edge Round Belt
Air Pressure: 5kgf/cm2
Power: Ac220v, 50/60 Hz, 1 Phase
Pcb Convey Directon: L-r ( Or R-l)
Front Rail Fxed ( Or Rear Rail Fxed)
Conveyor Height:900+/-50mm
Conveyor Speed: 10m/s

contact us：shaoyong@smthelp.net    WhatsApp：+86 137 6048 1664

The Manual Lift Gate Conveyor is used when a passage way is required in a production line.
By manual lifting the conveyor section, access is gained to the rear of the line. (semiautomatic).
PLC Control system.
Cylinder assisted lifting motion
Width adjustment by hand crank.
Pneumatic locking device installed to enhance safety.
SMEMA compliant.
CE certified

contact us：shaoyong@smthelp.net     WhatsApp：+86 137 6048 1664 

The PCB NG/OK Unloader is used for good/bad PCB separation. The OK and NG PCB
after being tested by test machine can be separated and sent to magazines
Omron PLC Control system.
Touch screen easily operation.
Good and bad PCB’s can be separated automatically with magazine rack.
Multiple pitches selectable.
Direction from left to right, or right to left (optional).
SMEMA compliant.
RoHs .CE certified

contact us：shaoyong@smthelp.net    WhatsApp：+86 137 6048 1664

User friendly touch screen control panel;
Uninterrupted loading;
Smooth and parallel with adjustments
Small machine footprint;
Automatically senses stack height
Pass-through function
SMEMA compatible
PCB Size – 50 mm L x 50 mm W to 400 mm L x 350 mm W ( Optional: 460mm width)
PCB Stack Capacity – 400 pcs. (0.6 mm thickness) or 240 mm (9.45″)
stack height PCB Thickness – 0.4 mm min. (0.016″ min.)2.5 mm max. (0.098″ max.)
Conveyor Direction – Left to right (standard) or right to left (optional) operation
Conveyor – 3 mm Edge Belt
Air Supply Pressure – 5-6 Kg/cm2 (70-85 psi)
Air Consumption – 30 l/min (1 CFM)
Voltage – 220 VAC, 50/60 Hz Power 150 VA max.
Machine Dimensions – 728 mm L x 700 mm W x 1127 mm H
Net Weight – 160kg
Shipping Weight – 200 Kg

contact us：shaoyogn@smthelp.net    WhatsApp：+86 137 6048 1664

This equipment is used SMT circuit board production line operating upper and lower plates.
Magazine quantity: upper 1pc, bottom 1pc.
Tank Replacement time: about 30 seconds or a user specified
step select: 10,20,30,40 mm or user
spec. 110V or 220V, single phase max 250VA.
Barometic pressure from 4-6 bar, up to 10/min
Flexible platform to suit standard magazines. Regulated pressure on attached pneumatic pusher. Pusher position adjustable to centre of the magazine. User friendly “soft touch” LED membrane controlpanel.

contact us：shaoyong@smthelp.net    WhatsApp：+86 137 6048 1664

This equipment is used SMT circuit board production line operating upper and lower plates.
Magazine quantity: upper 1pc, bottom 1pc.
Tank Replacement time: about 30 seconds or a user specified
step select: 10,20,30,40 mm or user
spec. 110V or 220V, single phase max 250VA.
Barometic pressure from 4-6 bar, up to 10/min
Flexible platform to suit standard magazines. Regulated pressure on attached pneumatic pusher. Pusher position adjustable to centre of the magazine. User friendly “soft touch” LED membrane controlpanel.

contact us：shaoyong@smthelp.net    WhatsApp：+86 137 6048 1664

How length conveyor do you need?
What is the maximum width of you PCB?
Do you need inspection with lighting
Do you need dual rail?
Do you need cover with cooling fan?
Do you need buffer bad boards?
Do you need working table both side?
We are able to customize conveyors